If you are looking for high-quality products, please feel free to contact us and send an inquiry, email: brad@ihpa.net
Titanium Carbide: An Introduction
The chemical formula of
Titan carbide
TiC is a gray, metal-like, solid with a face centered cubic lattice. Its molecular weight (59.89) is also 59.89. The melting temperature of titanium carbide ranges from 3140+90degC to 4820degC. Its relative density is 4,93 and its hardness is higher than 9.
Titanium carbide, while insoluble in water is soluble with nitric acids and aqua regia. It is stable when the temperature is below 800. However, when it reaches 2000 it will be corroded.
Carbonized TiO2 or TiO2 powder is produced by heating TiO2 in an electric oven to 2300-2700degC.
Titanium carbide, which can be used as an abrasive and electrode for arc lights and hard alloys can be made.
Titan carbide can be prepared in several different ways
Reduce carbothermic toxicity using a reduction method
The reaction temperature range for carbon black is between 1700 and 2100 degrees Celsius. The chemical reaction formula:
Ti powder and carbon dust react to form TiC. The chemical reaction formula: Ti(s),+C(s),=TiC. The application of this method will be limited because it’s difficult to make sub-micron Ti powder. The reaction above takes between 5 and 20 hrs to complete. The reactants agglomerate and require additional grinding processes to achieve fine particles. Granular TiC powder. After ball milling, the fine powder needs to be chemically purified to produce a pure product.
Chemical vapor deposition
The synthesis method uses the reaction between TiCl4, and H2 and C. TiC The monofilament is soaked with crystals. The TiC produced by this method is subject to strict limitations on output, and in some cases even quality. It is important to be aware that the HCl in TiCl4 as well as its product can be highly corrosive.
Microwave method
Use microwave energy to heat nano-TiO2 and carbon as raw materials. The dielectric loss in the high frequency electric field is used to convert microwave energy into heating energy.
Blast impact method
Preparing the precursor requires mixing the titanium dioxide powder with the carbon powder in a specific proportion. The powder density is set at 1.5g/cm3, the outer cylinder is made of metal, and the laboratory placed inside. It is then placed in an airtight container made by yourself for the experiment. The detonation powder will be collected after the shock wave. After sieving the black powder, impurities like iron filings and large particles are removed. After soaking in aqua regia overnight, the black powder is turned brown. The powder is then put into an muffle furnace for 400degC and calcined 400 minutes.
High-temperature self-propagating synthesis
(SHS) SHS is derived by an exothermic process. When heated at the right temperature, fine-grained Ti Powder has a high degree of reactivity. The combustion wave produced after ignition will pass through Ti and the C reactants, and the reaction heat generated by Ti and the C will generate TiC. SHS has a reaction time of less than a second. The synthesis requires fine, high-purity Ti powder for the raw material and output is limited.
Reaction ball grinding technique
The reactive ball milling technique is a method that utilizes the chemical reactions between metal powder and other materials or compounds during the ball grinding process to create the desired material. Reactive ball milling is used to prepare nanomaterials using a high energy ball mill. This is mostly used to make nanocrystalline materials. The reaction ball grinding mechanism can be divided in two categories: the first is the mechanically induced high-temperature self-propagating synthesis reaction (SHS), while the second is the reaction ballmilling with no obvious exotherm and a slow reaction process.
Uses of titanium carbide
1. Use as an additive for metal bismuth and zinc melting crucibles and to prepare HDD large-capacity memories devices and wear-resistant semiconductor films.
2. This is an essential component of cemented carburide, which is used as a steelmaking deoxidizer.
3. As a cermet it is known for its high hardness, corrosion-resistance, and thermal stability.
(aka. Technology Co. Ltd., a trusted global chemical supplier & manufacturer has over 12 years experience in providing super-high-quality chemicals and nanomaterials. The titanium carbid Please note that the products produced by our company are of high purity and have low impurities. Please. Contact us if necessary.
Titanium carbide, while insoluble in water is soluble with nitric acids and aqua regia. It is stable when the temperature is below 800. However, when it reaches 2000 it will be corroded.
Carbonized TiO2 or TiO2 powder is produced by heating TiO2 in an electric oven to 2300-2700degC.
Titanium carbide, which can be used as an abrasive and electrode for arc lights and hard alloys can be made.
Titan carbide can be prepared in several different ways
Reduce carbothermic toxicity using a reduction method
The reaction temperature range for carbon black is between 1700 and 2100 degrees Celsius. The chemical reaction formula:
TiO2(s)+3C(s)=TiC(S)+2CO(g).
Direct carbonization
Ti powder and carbon dust react to form TiC. The chemical reaction formula: Ti(s),+C(s),=TiC. The application of this method will be limited because it’s difficult to make sub-micron Ti powder. The reaction above takes between 5 and 20 hrs to complete. The reactants agglomerate and require additional grinding processes to achieve fine particles. Granular TiC powder. After ball milling, the fine powder needs to be chemically purified to produce a pure product.
Chemical vapor deposition
The synthesis method uses the reaction between TiCl4, and H2 and C. TiC The monofilament is soaked with crystals. The TiC produced by this method is subject to strict limitations on output, and in some cases even quality. It is important to be aware that the HCl in TiCl4 as well as its product can be highly corrosive.
Microwave method
Use microwave energy to heat nano-TiO2 and carbon as raw materials. The dielectric loss in the high frequency electric field is used to convert microwave energy into heating energy.
Blast impact method
Preparing the precursor requires mixing the titanium dioxide powder with the carbon powder in a specific proportion. The powder density is set at 1.5g/cm3, the outer cylinder is made of metal, and the laboratory placed inside. It is then placed in an airtight container made by yourself for the experiment. The detonation powder will be collected after the shock wave. After sieving the black powder, impurities like iron filings and large particles are removed. After soaking in aqua regia overnight, the black powder is turned brown. The powder is then put into an muffle furnace for 400degC and calcined 400 minutes.
High-temperature self-propagating synthesis
(SHS) SHS is derived by an exothermic process. When heated at the right temperature, fine-grained Ti Powder has a high degree of reactivity. The combustion wave produced after ignition will pass through Ti and the C reactants, and the reaction heat generated by Ti and the C will generate TiC. SHS has a reaction time of less than a second. The synthesis requires fine, high-purity Ti powder for the raw material and output is limited.
Reaction ball grinding technique
The reactive ball milling technique is a method that utilizes the chemical reactions between metal powder and other materials or compounds during the ball grinding process to create the desired material. Reactive ball milling is used to prepare nanomaterials using a high energy ball mill. This is mostly used to make nanocrystalline materials. The reaction ball grinding mechanism can be divided in two categories: the first is the mechanically induced high-temperature self-propagating synthesis reaction (SHS), while the second is the reaction ballmilling with no obvious exotherm and a slow reaction process.
Uses of titanium carbide
1. Use as an additive for metal bismuth and zinc melting crucibles and to prepare HDD large-capacity memories devices and wear-resistant semiconductor films.
2. This is an essential component of cemented carburide, which is used as a steelmaking deoxidizer.
3. As a cermet it is known for its high hardness, corrosion-resistance, and thermal stability.
(aka. Technology Co. Ltd., a trusted global chemical supplier & manufacturer has over 12 years experience in providing super-high-quality chemicals and nanomaterials. The titanium carbid Please note that the products produced by our company are of high purity and have low impurities. Please. Contact us if necessary.